2003 mitsubishi lancer oil type




2003 mitsubishi lancer oil type

Article Navigation:
  • Photo
  • Mitsubishi Lancer Oils, Fluids, Lubricants — HOME1.INFO
  • Video
  • RELATED PAGES
  • Results 1 - 24 of Order Motor Oil - Vehicle Specific for your Mitsubishi Lancer and Your manufacturer will specify the oil change interval and oil type.

    Equip cars, trucks & SUVs with Mitsubishi Lancer Engine Oil from AutoZone . Get Yours Container Type. 1 qt. Bottle (4) SAE Oil Weight. 10W (7).

    Interesting fact! The Mitsubishi Group was established in Japan in 1870. And since then she has never changed her logo. Three well-known rhombuses symbolize three diamonds, "three whales", on which the whole concept of the concern rests: honesty, responsibility and readiness for cooperation.

    Mitsubishi Lancer Oil Change (L I4 DOHC): Change the oil in your ''07 Mitsubishi Lancer, with L I4 DOHC engine, to improve engine.

    2003 mitsubishi lancer oil type

    2003 mitsubishi lancer oil type

    Change the oil for 5W for winter only , instead of 10W These shiny specks may be metal flakes and could mean that there is a serious problem with your engine internals. How often do you get a flat tire on your vehicle per year? Engine lubricants Engine Type:

    2003 mitsubishi lancer oil type

    2003 mitsubishi lancer oil type

    2003 mitsubishi lancer oil type

    2003 mitsubishi lancer oil type

    2003 mitsubishi lancer oil type

    MITSUBISHI LANCER L 4-cyl Engine Code [E] - AMSOIL Online Product Application Guide

    Change the oil in your ''07 Mitsubishi Lancer, with 2. It is typically recommended that you change your vehicle's oil every 3, to 7, miles. However, this number can vary depending on your operating conditions, age of your vehicle, number of miles on your engine and your driving habits. Use of synthetic oils can help reduce engine wear and are advisable for older engines or if your typical driving involves extended periods of stop and go traffic. Consult your owner's manual or an online data base to determine what filters are appropriate.

    Begin by locating the lifting point. It is on the passenger side of the car, below the rocker panel and just behind the front wheel. Slowly lower the jack until the jack stand is supporting the car. Many hydraulic jacks are lowered by placing the open end of the handle over a knob and turning it counter-clockwise. Consult your owners manual for your jack if you don't know how to lower it. Never work underneath a car that is only supported by a jack.

    2003 mitsubishi lancer oil type

    The jack may slip or fail, resulting in serious injury or death. Locate the 17mm hex oil drain plug. It is on the passenger side of the car, facing backwards and is next to the exhaust pipe. Be sure that the drain pan is positioned so that it will catch the oil when it is streaming out of the pan. Always wear protective gloves and eyewear when working with motor oil. Be careful if your car has been running recently as the engine, transmission and exhaust may be very hot.

    Keep rags or towels nearby to wipe up any spills. Use a 17 mm socket wrench or box end wrench to loosen the oil drain plug until it is loose enough to turn by hand. Watch the draining oil for shiny specks. These shiny specks may be metal flakes and could mean that there is a serious problem with your engine internals. Replace the drain plug. Screw it in as far as possible by hand, then use the 17 mm socket or box end wrench to finish tightening it. Only tighten the drain plug until it is snug.

    2003 mitsubishi lancer oil type

    Over-tightening the oil drain plug can strip the threads or crack the oil pan. Locate the oil filter. It is on the passenger side of the oil drain pan and is most easily accessible from the front of the car. Reposition the oil drain pan so that it catches the oil that will spill when you remove the oil filter. Use your hand to turn the oil filter counter-clockwise until it comes off the threads. If the filter is too tight to loosen by hand, use an oil filter wrench.

    A wrench that fits over the top of the oil filter is ideal, as there is very little space on the sides of the oil filter. Lower the filter with the threads facing up to prevent spilling oil, then place it in the oil drain pan with the threads facing down. Place the threaded end of the oil filter onto the engine's oil filter threads, being careful to not get dirt or debris on the filter's gasket.

    Turn the filter clockwise by hand until it is snug. Tightening the filter should require a moderate amount of your strength, but not all of it. If the filter is difficult to turn at the beginning of its threads, stop!

    2003 mitsubishi lancer oil type

    You may be cross threading the oil filter. Re-align the oil filter and try again. Do not over-tighten your oil filter by using a wrench. Doing so may cause the oil filter seal to leak and will make removing the oil filter very difficult in the future. Locate the hood release lever. It is below the left side of the driver's console. Go to the front of the car and locate the hood release latch. It is under the hood and slightly towards the driver's side of the car. Place the end of the hood prop rod into the hole on the passenger's side of the hood marked by an arrow.

    Locate the oil filler cap. It is on the valve cover, towards the passenger side of the car. Pour 4 quarts of 10W oil into the engine. Use one hand to stabilize the funnel to help prevent spills. Consult your owner's manual if you think your operating conditions call for a different oil viscosity.

    How to replace valve cover gasket, spark plug seals and PCV 2002 Mitsubishi Lancer 4G94



    • Подписаться по RSSRSS
    • Поделиться VkontakteVkontakte
    • Поделиться на FacebookFacebook
    • Твитнуть!Twitter

    Leave a Reply

    Return to Top ▲TOP ▲